![]() ![]() Total number of prefixes in the current routing table. Table 7-8 Description of the display ipv6 routing-table statistics command output Protocol route active added deleted freed display ipv6 routing-table vpn6-instance vpn1 statistics # Display the statistics of the routing table of the VPN instance named vpn1. The value is an integer ranging from 0 to 4294967295. Number of times that the route is referenced. Keyword of the retrieval index of routes in the routing table. Stale.: indicates the routes with the stale flag. ![]() Relied: indicates the route that finds the next hop and outbound interface or the route that finds the tunnel during packet forwarding. NoAdv: indicates the routes that cannot be advertised.Īdv: indicates the routes that can be advertised. # Display detailed information about the route 200:0:1:2::1 of the VPN instance after the instance is enabled with VPN FRR. Outbound interface through which the next hop is reachable. The value 0x0 indicates that no tunnel is used or the tunnel is not set up. IPv6 address of the adjacent next hop through which the packet reaches the destination. Total number of destination networks or hosts.Īddress of the destination network or host. ![]() Table 7-6 Description of the display ipv6 routing-table vpn6-instance command output If the specified ip-prefix ip-prefix-name does not exist, the command displays all of the currently preferred routes. If the display ipv6 routing-table vpn6-instance vpna fc00:0:0:2000:: 0 longer-match command is used, four routes are displayed. If the display ipv6 routing-table vpn6-instance vpna fc00:0:0:2000:: command is used, only FC00:0:0:2000::/100 is displayed. If the display ipv6 routing-table vpn6-instance vpna fc00:0:0:2000:: 64 command is used, only FC00:0:0:2000::/64 is displayed. If the prefix length isĠ, all routes in the routing table of the VPN instance are displayed.įor example, there are four routes in the routing table of the VPN instance named vpna, FC00:0:0:2000::20/128, FC00:0:0:2000::/100, FC00:0:0:2000::/64, and FC00:0:0:1000::/64. If ipv6-address prefix-length longer-match is specified, the IPv6 routes with the destination address within the specified address range are displayed. If ipv6-address prefix-length is specified, the VPN routes that accurately match the destination address are displayed. When using the display ipv6 routing-table vpn6-instance vpn6-instance-name ipv6-address prefix-length command, you can select parameters in the command as required. This command without the parameter verbose displays the currently preferred routes only. How many outbound interfaces and next hops the route finds. It can be one of the following keywords:ĭisplays the summary of inactive routes only.Īn iterated route is counted as one route no matter Specifies the name of the IPv6 prefix list.ĭisplays integrated route statistics in the routing table of the VPN instance.ĭisplays the routes of a specified protocol.ĭisplays the routes of a specified protocol. Only the VPN routes in the address range are displayed. ipv6-address1 and ipv6-address2 together determine an address range. The value is an integer that ranges from 0 to 128. Specifies the length of the IPv6 address prefix. ![]() The value is a string of 1 to 32 case-sensitive characters without spaces, begin with a~z or A~Z.ĭisplays only the VPN routes that match the specified network and mask. The value is an integer that ranges from 2000 to 2999. If the specified ACL6 does not exist, information about all active routes is displayed. The value is a string of 1 to 31 case-sensitive characters without spaces.ĭisplays detailed information about active and inactive routes in the routing table of the current VPN instance. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |